PRINT 50 AN ALLY FOR THE ENVIRONMENT

PRINT 50 AN ALLY FOR THE ENVIRONMENT

Since the introduction of the emulsion 50 in Uruguay PRINT form base priming it has changed considerably because of the technical and economic advantages

We have made little emphasis on the environmental benefits of its use to the detriment of asphalt diluted for priming as in the case of the MC1. Diluted contains 30% volatile solvents evaporating end to the atmosphere photochemical smog impact on the greenhouse effect and the reduction of the ozone layer while PRINT 50 only emits water in curing.
Also, temperatures of handling and application of different types of primers lead to significant fuel economy as the PRINT 50 It is fully liquid at room temperature and water it is possible at temperatures as low as 40 to 50 ° C while the MC1 must be heated to 90 ° C or 80 to be applied correctly.
In recent years the use of PRINT 50 in Uruguay achieved:
- Reduce by 3000 tons of solvents emitted into the atmosphere
- Reducing CO2 emitted to the atmosphere because of its lower temperature manufacturing, handling and application
- Improving safety and health of workers by lower operating temperatures and avoid inhaling solvents
- Eliminate the risk of explosion in regadores trucks.
As for flammability and explosion hazard we should worry seriously and only in 2019 there were 2 accidents which fortunately had no fatal casualties but substantial material losses.
March 14 2019: Explosion of a tank RC2 in Maldonado http://www.maldonado.gub.uy/?n=38251&mm=Obras
In many countries of the world the use of diluted asphalt is prohibited, as is the case of Argentina and Spain, or at the least there are state policies that tend to reduce these products. In the US and Canada have guidelines for not using dilute solvent regulate their content or used out only from the time of ozone generation (usually summer).
It has recently been proposed that can not manufacture or market any diluted containing more than 0.5% by volume of volatile solvents evaporated at 260 ° C or less as determined by ASTM D402.
Uruguay should consider this path if we want to be an environmentally responsible country and protect the lives of workers.
For further information on the technical advantages we approached them a paper presented at the 9th Congress of the Road Uruguaya: https://bitafal.com.uy/wp-content/uploads/2017/10/9%c2%ba-CVU-Trabajo-Imprimaci%c3%b3n-con-emulsiones-mejoras-t%c3%a9cnicas-y-ambientales.pdf
EMULSIONES BITAFAL IN WORK

EMULSIONES BITAFAL IN WORK

emulsions IRRIGATION BITAFLEX 65 polymer modified P12, P25 and P40 and the 50 PRINT BITAFAL They are having a great performance in all works of surface treatment that is using the different areas in the country both in their application and end use.

They have good viscosity to prevent runoff and once in contact with the aggregate achieve high cohesion within minutes. The asphalt binder, adjusted penetration according to the time of year when we are working and the area of ​​the country where the work is executed, is further modified with elastomeric polymers that provide excellent resistance to traffic and weather.

The hundreds of km of works in major routes as 10, 13, 15, 19, 20, 23, 26, 45, 57, among others, are witness to the above and shown BITAFAL engagement with Uruguay road.

We invite you to view images of some of the newly built surface treatments.

EMULSION BITAFAL PRINT 50 SPACE STILL WINNING

EMULSION BITAFAL PRINT 50 SPACE STILL WINNING

Technical, economic and environmental advantages of the emulsion 50 PRINT BITAFAL They are positioning it against diluted MC1.

More and more works in Uruguay who are using the emulsion PRINT 50 as a protective layer of granular and stabilized bases. It has a very good ability to penetrate most bases used. Furthermore the rate of penetration and curing is significantly better compared to MC1, not to mention that all that is released into the atmosphere and the soil is water and not solvents.

We emphasize the importance of surface moisture of the base does not exceed 1% for the performance thereof is optimal. If the base is wet, means that the pores are filled with water and despite the PRINT 50 is water based, it will not be able to penetrate and surface.

Any questions or concerns about using it please consult the 0800 8425 or bitafal@bitafal.com.uy.

GRAVILLADOS NEW ROUNDABOUT ROUTE 10 And 16

GRAVILLADOS NEW ROUNDABOUT ROUTE 10 And 16

recently we conducted for the company Techint S.A.C.I. one graveled with our double spreaders in a new roundabout built between Routes 10 and 16.

The work was done in a couple of days only because of the great versatility of these self-propelled equipment to work on curves of small radii. They consisted of a primer emulsion Print 50, and then a modified double emulsion CHIPSEAL Irrigation 65 P25. Quality of work, both dosage and overlap could be seen both as technicians of the company Techint and the MTOP.

We attach some pictures of them to appreciate the quality of the terminations.

ALL PHOTOS ON HERE

Print 50 for treatment DUST


emulsion 50 PRINT BITAFAL Hoping it will be of interest to other municipalities, we extend the invitation to participate, you can write to

Anticipating the arrival of the heat and low humidity environment to multiply the effect of fine suspended, and have been conducting several test sections in different traffic conditions to evaluate their performance and durability.
Were tested dosages of 0.6 to 1.0 L / m2, with the optimum performance for dust control is at low doses and releasable traffic almost immediately and are not accumulation zones emulsion. For all these tests has been carried out prior sweep the surface and has cared moisture in it was low for better performance of the emulsion.
In one of the test sections was used as 2-6 mm gravillín immediate release protection traffic without the gravillín interfere with curing or penetration depth since the absorption rate at the base is very fast. With this technique it is possible to urban jobs without cutting the road in no time.
After heavy rains last week some edges of the test sections were eroded by rain which allowed us to check the depth of action of the PRINT 50 and enclosed in photographs.
We estimate that the lifetime of the dust treatment performed with this emulsion, due to the depths reached, must be above 12 months.

We use own and third party cookies to help us optimize your visit to our website and also to improve service delivery and thus adapt to their most relevant and useful to better their experience needs. When you click OK to continue with navigation and thus confirm that you have read the information and accept the activation of cookies.

You can allow or reject use at any time can change the Configuration Options Privacy - Cookies Policy -

Privacy settings

When you visit a website, you can store or retrieve information in your browser, mainly in the form of cookies. Check your personal services cookies here.


We track anonymous user information to improve our website.
.
  • _ga
  • _gid
  • _gat

Decline all Services
Accept all Services